Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Home Additions & ADU: The Fort Worth Owner’s Guide
If you’re reading this, you probably already know Boral makes some of the most specified trim, siding, and exterior cladding products on the market, and you’re either planning a home addition or ADU that specs Boral materials, or you’ve got Boral product on an existing addition that’s showing wear. A full home addition in Fort Worth runs $45,000 to $130,000, and if the job includes Boral trim, siding, or foundation elements, the material choice matters more than most people realize. Bradford Remodeling Co Fort Worth installs and repairs Boral-compatible materials on additions and ADUs across Tarrant County, and we stock the common profiles so you’re not waiting three weeks on a special order. Most owners discover a Boral component has failed during a routine inspection, after a hailstorm, or when a corner trim piece starts pulling away from the framing under North Texas heat.
One thing to know before we go further: Bradford Remodeling Co Fort Worth is an independent contractor. We’re not affiliated with Boral or its distributors. We work with Boral products because they hold up in Fort Worth’s specific climate, and we know the installation tolerances from doing it on real job sites, not from a brochure.
Which Boral Models This Applies To
Boral’s product line breaks into a few families that show up on Fort Worth additions and ADUs. The big ones are TruExterior Trim and Siding, Boral Versetta Stone, and Boral Roofing (concrete and clay tile). Each has its own compatibility rules, and that’s where we see owners get burned buying the wrong replacement part or profile.
On the TruExterior side, the poly-ash material comes in board profiles, corner boards, fascia, and trim boards sized from 1×4 up to 1×12, with specialty profiles like beadboard and nickel-gap. The gotcha on TruExterior is the crown and reveal profile matchup: Boral’s corner boards have a specific thickness (typically 5/8″ or 1-1/4″) and if you buy a generic composite corner that’s off by an eighth of an inch, the siding lines won’t lay flush. We see this regularly on additions where a homeowner or a previous contractor patched a section with a fiber-cement board and then the joint opened up a year later. For Versetta Stone, the panels come in 8″ nominal heights with either a flat or ledgestone profile, and the panels are 36″ wide. They interlock with a screw flange system, so a “part” failure isn’t a cracked stone; it’s a broken flange or a panel that was pinned too tight and bowed in the heat. Fort Worth’s freeze-thaw cycles are mild compared to the Panhandle, but the summer heat expansion on a dark-colored Versetta panel installed without an expansion gap is a real failure point.
Our rule on OEM versus aftermarket for Boral: structural and weather-exposed pieces are worth OEM. Trim boards, corner boards, and roof tile perimeter pieces take the brunt of Fort Worth storms. A quality aftermarket equivalent is fine for interior casing or decorative applications, but for anything that keeps water out of the wall assembly, we don’t play the “close enough” game. The manufacturer’s warranty only applies to the product, not the labor, which is why our 365-Day Done Right Promise matters: if we install a Boral-compatible piece and it fails inside the first year, we come back and correct it at no charge. The product warranty is Boral’s. The installation warranty is ours, and it’s in writing before we lift a tool.
Styles & brands we work with
Signs Your Boral Home Additions & ADU Is Failing
- Corner trim pulling away at the joint. Boral TruExterior corner boards don’t warp like wood, but if they were installed without proper fasteners or with too few, the thermal expansion in Fort Worth’s 100-degree summers works the fasteners loose. You’ll see a gap open at the miter, and then water finds it.
- Caulk line cracking repeatedly. If you’ve re-caulked a Boral trim joint twice in eighteen months and it keeps splitting, the board behind it is moving. That’s a substrate or fastener issue, not a caulk problem. New caulk over a moving substrate fails the same way the previous bead did.
- Versetta Stone panels bowing outward. This is nearly always a fastening issue. A panel that’s snugged too tight to the wall can’t expand, so it creases or bows in the middle. We inspect for proper 1/8″ spacing and re-pin the flange correctly instead of trying to flatten a bowed panel with more screws.
- Efflorescence or chalky residue on stone and tile. On Boral roof tile and Versetta Stone, a whitish haze means water is moving through the surface and carrying minerals out. In Fort Worth, with our clay-heavy soil and hard water, this shows up faster than on the coast. It’s worth investigating before it becomes spalling or freeze-damage in a rare cold snap.
- Cracked or missing roof tiles at the eave line. Concrete and clay tile at the eave takes impact from hail, but also from ladder foot pressure and gutter work. Loose or broken tile at the drip edge lets water behind the tile field, and that failure travels inward fast.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
The lead range for a Boral-compatible home addition or ADU project in Fort Worth is $45,000 to $130,000, and the spread is driven by the scope: a small single-room addition with standard Boral trim and Hardie-type lap siding lands well under $100,000, while an ADU with a separate kitchen rough-in, its own electrical subpanel, and Boral Versetta Stone accents will push the top of that range. If we’re replacing Boral product on an existing structure rather than building new, the work is scoped and priced separately: a TruExterior corner board replacement with new flashing and sealant typically runs $600 to $1,800 per corner depending on two-story access, and a Versetta Stone panel repair runs $850 to $2,500 for removal, inspection, and re-installation with correct spacing. Parts are broken out on the written quote. Labor is broken out on the written quote. You’ll see exactly what each line costs before we start, and the price doesn’t move at the door.
Every project, whether it’s a full ADU or a single trim board, gets a written price before work begins. That’s not a courtesy; that’s The Garrison Standard, and it’s non-negotiable. Materials are documented by brand, profile, and quantity. The 365-Day Done Right Promise covers our installation work for a full year. If the Boral product we installed fails inside that window because of how we put it in, we return and correct it at no charge. If the product itself fails and the manufacturer’s spec wasn’t met, that’s on us too. We don’t hide behind supplier warranties when our install was the problem.
DIY or Call Us?
There’s a bright line here. If you’re looking at a Boral TruExterior board that’s still flat, still seated, and just needs a repaint or re-caulk at an interior joint, that’s a Saturday job. Use the right sealant for poly-ash substrates and follow the gap schedule on the manufacturer’s data sheet. If the board itself is cracked, the flange on a Versetta panel is broken, or the trim is pulling away from framing, stop. That’s not cosmetic, and it’s not a patch over it and forget it situation.
Roof tile work on a Boral tile roof is a hard pass for DIY. Concrete tile is heavy, and walking a tile field the wrong way breaks more tiles than it saves. Fall risk is real, and tile field failure at the eave is the kind of thing that turns into structural water damage inside six months in a spring storm. Same logic applies to lifting stone panels off a wall assembly to find what’s moving behind them. If you can’t see the substrate, you’re guessing. We’ve corrected enough DIY “fixes” around Fort Worth to say it plainly: a failed patch costs more than a correct repair would have on day one.
If you’re not sure which side of the line you’re on, call the shop at (682) 204-4897. A live person answers, you’ll describe what you’re seeing, and we’ll tell you whether it’s a caulk gun job or a service call. No charge for the conversation.
FAQs
Boral TruExterior carries a 20-year limited warranty on the product itself, and with correct installation and regular paint maintenance, we expect 25 to 30 years of service from it in North Texas. The material won’t rot, which is the main failure mode it eliminates over wood. The failure risk shifts to fasteners and installation, which is why our 365-Day Done Right Promise covers the labor and the install for a full year. Call (682) 204-4897 if you want an honest assessment of what’s on your house and how much life it really has left.
Yes, in many cases a single board or corner section can be spliced or replaced without tearing out the full elevation. The limitation is profile matching. Older installations may have a profile that Boral has since revised, so we’ll check the stampings and dimensions before ordering. Most Fort Worth additions and ADUs built in the last ten years are still on current profiles, and we stock the common sizes. Call (682) 204-4897 with a photo and a measurement, and we can usually tell you on the phone whether it’s a patch or a full run.
A single corner board or fascia repair typically takes half a day to a full day on site, including flashing replacement and sealant cure. A full elevation of siding, depending on two-story access and window count, runs three to seven working days. We scope the timeline at the same time we price it, so you know both before we start. A live person answers the phone 24/7, and we’ll give you a straight answer on scheduling.
We stock the common TruExterior trim profiles and standard Versetta Stone panels, and we order specialty profiles through our supply chain with delivery timed to your schedule. You don’t have to chase down a lumberyard. We handle the material, the freight, and the storage, and it’s all on the written quote. Call (682) 204-4897 and we’ll check stock while you’re on the line.
Straight scope, firm price, no surprises at final walkthrough. That’s the way Curtis Lane runs every job. If our installation fails within one year, the 365-Day Done Right Promise means we come back and correct it at no charge. The warranty is written into your contract, and you’ll have a signed copy in hand when we close out the job. If the product itself fails under the manufacturer’s window, we’ll help you work the claim and handle the re-install. You won’t be chasing a supplier on your own.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth at Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
