Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Fence Installation: The Fort Worth Owner’s Guide
CWS fence installation in Fort Worth typically runs $3,500 to $9,000 for a full property line, and we stock the parts to do it right the first time. The most common call we get starts the same way: a homeowner notices a gate dragging, a post leaning after a storm, or a section that never sat level since the day it was put in. Most CWS fence failures in our area come down to three things: post depth cut short, wrong fasteners for Texas clay soil, or a gate frame that was never shimmed square. If you’re chasing a sagging gate or fence panels that skew every August, you’re not looking at a mystery; you’re looking at an installation problem. We can correct it, and we’ll price it in writing before the first post hole is dug.
One thing to know from the start: Bradford Remodeling Co Fort Worth is an independent contractor. We’re not affiliated with CWS. We install and repair CWS fence systems because we know the product line, and we treat it with the same discipline we bring to a full kitchen gut or an addition.
Which CWS Models This Applies To
CWS fence systems in Fort Worth show up most often as cedar privacy fence, ornamental steel, and the occasional composite panel system. The compatibility question that matters for your wallet is the post and rail spec. CWS ornamental steel panels are designed around 2-inch square posts, and sections come in standard widths of 6 feet and 8 feet. We measure from post center to post center before we order or fabricate panels; guessing gets expensive fast.
For wood privacy fence, the CWS-style construction is pine or cedar pickets over pressure-treated 2×4 rails, with posts set a minimum of 24 inches deep. That last number is not optional in Fort Worth. Our clay soil expands and contracts through the season, and posts set at 18 inches will heave by their third summer. That’s a checkable fact, and it’s the kind of thing that separates a fence that lasts 15 years from one that dies in five.
As for parts: you’ll see OEM CWS components and aftermarket equivalents. For ornamental steel, aftermarket post caps and brackets from a decent Texas supplier are fine. For structural parts like the gate frame hinges and post collars, use the OEM-style heavy gauge material. We won’t put a big-box hinge rated for a screen door on a CWS steel gate; that gate weighs more than it looks, and the hinge is the first thing to fail.
Styles & brands we work with
Signs Your CWS Fence Installation Is Failing
- Gate drags or won’t latch by late summer. Fort Worth’s clay soil moves, and when a gate post shifts, the gate frame twists. The latch no longer lines up. You can shim the hinge side, but if the post is moving, the real fix is resetting it in concrete below the frost line.
- Posts lean after a storm. If multiple posts in a row tilt the same direction, the original install didn’t set them deep enough, or it used dry-packed concrete that cracked. A single leaning post is an accident; a row of them is a pattern.
- Pickets warp or bow away from the rails. That’s usually a moisture issue: untreated cedar against pressure-treated rails, or the original installer used drywall screws instead of coated deck screws. In Fort Worth humidity, uncoated fasteners rust in two seasons and the pickets let go.
- Rust bleeding from post caps or hinges. Galvanized hardware looks fine for a year, then weeps rust streaks down a white fence. Spec the stainless or vinyl-coated hardware up front, or plan on replacing it every few years.
- Concrete footings cracked at the base of steel posts. When concrete is poured too wet or mixed too thin, it spalls. Once water gets into those cracks, the post socket corrodes from the inside. That’s a replacement, not a repair.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Full CWS fence installation in Fort Worth lands between $3,500 and $9,000 for most residential properties. The spread comes down to linear footage, fence height, whether we’re pulling the old line or starting fresh, and how much gate hardware is in the scope. A 150-foot cedar privacy fence with two gates usually sits near the middle of that range. A 300-foot ornamental steel run with custom gate fabrication runs at the top.
Our written price includes removal of the old fence if needed, concrete post setting at proper depth, all hardware, all pickets or panels, and haul-away. We don’t price the material and then bill the labor separately; you see the total before we start. If we hit rock or a hidden utility line, we call you with a number before we change course. No numbers move at the door. The completed installation carries our 365-Day Done Right Promise: if anything on that fence fails within the first year, we come back and correct it at no charge.
DIY or Call Us?
A homeowner in Fort Worth can absolutely replace a picket, tighten a hinge screw, or sand a rough gate edge. Those are one-hour jobs. Where DIY goes wrong is post setting. Digging a 24-inch hole in Texas clay is a hard afternoon; digging twelve of them, getting them plumb, and mixing concrete that won’t crack is a multi-weekend project that usually ends with a call to us anyway. The other spot to be careful: removing old posts set in concrete. A rotted post with a buried concrete ball weighs two hundred pounds. If you’re levering it out with a truck and a chain, you can pull it through your neighbor’s fence. We do this with a jack and a saw, and we do it standing. Straight scope, firm price, no surprises at final walkthrough.
For a CWS fence that needs matched parts and a true install, call Bradford Remodeling Co Fort Worth at (682) 204-4897. The estimate is free, and it’s written.
FAQs
A properly set CWS fence in Fort Worth clay and sun lasts 15 to 20 years for wood, longer for ornamental steel. The variables are post depth, concrete quality, and whether the rails were spaced for our humidity swings. Shallow posts fail first. Call (682) 204-4897 and we’ll check what’s already in the ground before you pay for a full replacement.
Yes, if the posts are still solid and the rails are intact. We reset gates, shim frames, and replace individual sections without ripping out the good fence. If the failure is below grade, a repair usually costs less but won’t hold as long. We’ll tell you which one we’d do on our own house.
Most residential installs take three to five working days from post setting to final gate hardware. Wait time depends on material availability and our current schedule. We’ll give you a start date and an end date in the written estimate, and we hold to those dates.
We keep common CWS-compatible post caps, gate hinges, latches, and hardware on the truck for same-week fixes. Panels and full post sets get ordered to your measurements. We also work with KraftMaid, Cambria, and Silestone for interior projects, but fence systems are stocked to spec, not guessed.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth at Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
