Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Kitchen Remodeling: The Fort Worth Owner’s Guide
If you’re holding a failed Barrette cabinet hinge, a warped drawer glide, or a cracked end panel from a Barrette cabinet line, here’s the straight answer: we stock and install Barrette-compatible kitchen cabinet and hardware parts across Fort Worth, and a typical cabinet repair or partial cabinet replacement runs $400 – $1,800 on the parts-and-labor side, while a full Barrette cabinet package install in an existing Fort Worth kitchen runs $4,000 – $13,000. That’s the range you should plan around. Most owners discover the failure the same way: a door that won’t stay closed, a drawer that catches mid-pull, or a shelf bracket that finally gave out under the weight of a cast-iron Dutch oven.
We’re an independent Fort Worth remodeling contractor. We are not affiliated with Barrette, and we don’t claim to be. But we work with their cabinets and hardware regularly, and we know where their components fail and what it costs to make it right.
Which Barrette Models This Applies To
Barrette cabinetry shows up in Fort Worth homes under a few different badges depending on the builder and the year. You’ll see Barrette as a hardware brand on cabinet doors and drawer boxes, and you’ll also see their components inside semi-custom lines sold through regional kitchen suppliers. The part you need depends on which generation of hardware your cabinets carry: older Barrette hinges use a 35mm cup bore with a 1/2-inch overlay, while newer soft-close versions use the same cup bore but a tighter 1/4-inch reveal. That measurement matters more than the brand name on the hinge. If you replace a soft-close hinge with a standard overlay hinge, the door sits proud of the frame by an eighth of an inch and you will notice it every time you walk past.
The practical takeaway: measure the bore and the overlay before you buy. Or call us and we’ll identify it on the truck. We carry OEM Barrette hinges and glides plus quality aftermarket equivalents from Blum and Salice, which are interchangeable in most Barrette frames. The aftermarket option usually costs 20 – 30% less and lasts just as long, but there’s one gotcha: Barrette’s older trash-can pull-out slides use a 3-inch mounting spread that most modern aftermarket slides do not match. You either order the OEM part or you replace the whole pull-out assembly. We learned that one the hard way on a kitchen off Camp Bowie, and we keep both options stocked now.
Styles & brands we work with
Signs Your Barrette Kitchen Remodeling Is Failing
- A cabinet door sags by more than 1/8 inch at the latch corner. This usually means the hinge’s internal spring or soft-close damper is worn. The hinge still functions, but the door will keep dropping until you shim it or replace it.
- A drawer box grinds or catches halfway through the pull. In Fort Worth’s dry summers and humid springs, wood drawer boxes expand and contract against the metal glide. Once a Barrette glide loses its ball-bearing race, the drawer will never run smooth again. Replacement is the honest fix.
- The soft-close feature stops working on one door but still works on its neighbor. This is the damper. Barrette’s dampers are small, and once they lose hydraulic fluid, the door slams. The hinge mount may be fine, but the damper needs replacement.
- A corner shelf bracket or cam lock has cracked at the shelf pin. Barrette uses plastic cam locks in some of their mid-range lines, and under load they fail. Swapping to a metal bracket solves it permanently.
- The cabinet face frame has pulled away from the cabinet box at the top rail. This is a structural failure, often from moisture under a Fort Worth sink base. You need the face frame re-fastened and the substrate checked, not just a new hinge.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Barrette-compatible cabinet repair or replacement in Fort Worth, here’s what you should expect on installed pricing:
- Hinge or glide replacement (single unit): $40 – $120 installed, including the part
- Full kitchen hinge and glide replacement (20+ doors/drawers): $600 – $1,800
- Partial cabinet box or face frame repair: $400 – $1,200 depending on substrate condition
- Full Barrette cabinet package install: $4,000 – $13,000
- Countertop installation to match new cabinets: $2,000 – $6,500
Every price is written before any work starts, and it doesn’t move at the door. That’s The Garrison Standard we operate under. We don’t change order you on a hinge replacement because we found “unexpected damage.” We scope it, we price it, and we hand you the written quote. If the repair fails inside a year, the 365-Day Done Right Promise brings us back to correct it at no charge. That’s not a verbal promise. It’s a written guarantee you get at job close, signed.
DIY or Call Us?
Cabinet hardware replacement isn’t dangerous in the way that high-tension garage springs or electrical work is. You won’t hurt yourself swapping a hinge. But you can absolutely turn a $60 fix into a $400 repair if you strip a bore hole, mis-drill a replacement plate, or put a soft-close mechanism on backwards and force it. The most common Fort Worth DIY failure we see is a homeowner using drywall screws to re-mount a cabinet hinge. They bite, but they don’t hold in the face frame, and within six months the door sags worse than it did before.
If the door closes, but it doesn’t close right, you can check the hinge screws for tightness and check the overlay with a straightedge. If the bore is blown out or the face frame is pulling away, call us before you drill anything. Curtis Lane will tell you the same thing on the phone: (682) 204-4897. Straight scope, firm price, no surprises at final walkthrough.
FAQs
In normal use, Barrette soft-close hinges last 10 – 15 years in Fort Worth, but the dampers usually fail first, often by year 8. Glides last 12 – 20 years unless a drawer is overloaded. Our dry summers don’t kill hardware directly, but the humidity swings in March and October put more movement stress on wood boxes, which accelerates glide wear. Call (682) 204-4897 if a door or drawer is starting to fight you.
No. Once a soft-close damper loses its fluid or a ball-bearing race gets flat spots, the hardware cannot be rebuilt. The only honest repair is a replacement part. We’ve tried cleaning and re-packing glides, and the fix doesn’t hold. Call (682) 204-4897 and we’ll replace it with the right part the first time.
A single hinge replacement takes us 20 – 30 minutes on site. A full kitchen of hinges and glides, including adjustment and alignment, is a one-day job, usually 4 – 6 hours. We protect your countertops, we sweep the floor before we leave, and the site is clean before we hand you the guarantee. Call (682) 204-4897 to schedule.
Yes. We keep the most common Barrette hinge overlays, soft-close dampers, and glide sizes on the truck, plus compatible Blum and Salice equivalents for the 35mm cup bore. The outlier is the older 3-inch trash-can pull-out slide, which we order from the manufacturer. Either way, you get a written price before any work starts. Call (682) 204-4897 and we’ll tell you what’s in stock today.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth at Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
