Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Roofing: The Fort Worth Owner’s Guide
Barrette roofing typically costs $8,000 to $20,000 for a full replacement in Fort Worth, and we stock Barrette-compatible flashing, ridge caps, and underlayment components on our trucks. Most homeowners discover a Barrette part failing after a North Texas storm, usually a hail event or a wind gust that lifts a corner of flashing, or they spot a water stain on the ceiling and trace it back to a cracked ridge cap. We handle the parts matching and installation so you’re not guessing at the supply house.
Barrette is a manufacturer of metal roofing systems widely used across Tarrant County, from Aledo to Crowley. Their panels run in specific profiles, and that’s where most parts problems start. A Barrette panel that’s been on a Fort Worth roof for eight to ten years is usually still structurally sound, but the ancillary parts – the closures, the foam strips, the screws with their rubber washers – those fail first. The Texas sun bakes the rubber, and the temperature swings from 38 degrees to 104 degrees in a single week work screws loose. We see it on homes in Wedgwood, Ridglea Hills, and out toward Benbrook all spring long.
Bradford Remodeling Co Fort Worth is an independent service provider. We are not affiliated with Barrette as a manufacturer, but we work with their product lines daily and match parts by panel profile and gauge, not by guessing.
Which Barrette Models This Applies To
Barrette’s metal roofing line spans standing seam, ribbed agricultural panels, and corrugated profiles, and the part you need depends entirely on which of those is on your roof. The compatibility gotcha that trips up Fort Worth owners is this: Barrette’s 1¾” ribbed panels and their 2″ standing seam lines take different closure strips, and they are not interchangeable. A closure strip cut for a 1¾” rib will sit loose on a 2″ seam and leak within a season. We measure the panel profile with calipers before ordering anything, which is why we never trust a photo and a hopeful guess.
On the OEM-versus-aftermarket question: Barrette’s own closures and screws are specified to their panel gauge, and we use OEM for anything under manufacturer warranty. For out-of-warranty roofs, quality aftermarket closures of the same profile and foam density work fine and often cost 15 to 20 percent less. We only use aftermarket parts with documented material specs that match Barrette’s profile dimensions. The roof doesn’t know whose logo is on the box; it knows whether the part fits.
If you can get to a gable end safely, check the underside of a panel near the eave. Barrette often prints the profile code there. If not, our field team identifies it from the panel’s rib spacing and gauge before the first order goes in.
Styles & brands we work with
Signs Your Barrette Roofing Is Failing
- Water stains on ceilings or walls after a rain, but not always in the same spot. This usually means a closure strip at the ridge has split or a screw’s rubber washer has hardened and lost its seal. Water enters at the roof deck and travels along the purlin or truss, so the stain shows up ten feet from the actual leak.
- Loose or missing screws scattered in gutters or on the ground after wind. The rubber washers on any metal roof last seven to ten years in Fort Worth’s UV before they crack. When the washer fails, the screw backs out, and the hole it leaves becomes a direct water channel.
- Ridge cap that rattles or shifts during high wind. Barrette ridge caps rely on compression from the closures beneath them. Once those closures degrade, the ridge cap has play in it, and a 60-mph gust off the plains will start working it loose.
- Visible daylight through the roof from inside an attic at the ridge or eave line. That’s a failed closure strip or a separated lap joint. It’s not marginal, and it’s not going to seal itself. We’ve pulled panels in the Stockyards district where the closure had fully disintegrated into powder.
- Exposed or rusted screws with staining around the screw heads. Rust means the washer is gone and water has been working on the steel. In a few more seasons, the screw shank rusts through, and the panel lifts at that anchor point.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Barrette roofing work in Fort Worth, a targeted repair, such as replacing ridge closures, new screws, and sealing lap joints, runs $400 to $1,800 depending on roof size and access. A full Barrette roof replacement on a typical Fort Worth single-story home falls between $8,000 and $20,000. The range is driven by roof pitch, decking condition if it needs replacing, and whether we’re matching an existing panel profile or quoting new material.
Every quote is a written price before any work starts. You’ll get a line item for parts, a line item for labor, and a line item for disposal if any. No number moves at the door. If our crew finds rotted decking under the panels, we document it, show you, and give you a written change before we cut. That’s The Garrison Standard, and it’s non-negotiable. When work is done, you get a signed written guarantee under the 365-Day Done Right Promise: if the repair fails within a full year, we come back and correct it at no charge.
DIY or Call Us?
Here’s the honest split. You can safely inspect from the ground with binoculars: look for missing screws, lifted ridge caps, and rust staining around fasteners. You can also climb into your attic during daylight and look for pinpoints of light at the ridge and eave. Those two checks will tell you if you need us.
What you should not do is walk a metal roof to reseat closures or back out and replace screws. Metal roofing in the morning is slick with dew, and one wrong step off a purlin can send you off the eave. The bigger issue is that the wrong replacement screw or the wrong closure profile will fail quietly and then leak louder. A $6 hardware store closure that doesn’t match a Barrette profile costs a lot more in ceiling repair a year later. Call Curtis Lane and the team at (682) 204-4897. We’ll send a background-checked, uniformed tech to measure the profile, quote the parts, and give you a written price before you decide anything.
FAQs
The panels themselves will usually run 35 to 50 years, but the screws, washers, and closures are seven to ten year wear items in North Texas heat. A $12 replacement screw matched to the panel profile and properly seated keeps a $40,000 roof from leaking at year nine.
Closures and screws are replaced, not repaired; there’s no patch that restores a broken closure’s seal. Damaged panels themselves can sometimes be bent back and resealed if the damage is at a lap edge, but a punctured or creased panel is a replacement. Call (682) 204-4897 with a photo of the area and we’ll tell you which one you’re dealing with before we ever charge you a trip fee.
A targeted closure and fastener replacement runs half a day to a full day. A full Barrette roof replacement on a standard single-story Fort Worth home takes three to five working days, depending on sheathing condition and whether we’re matching an existing profile or ordering new. Every project gets a firm schedule in the written scope.
We stock the common Barrette closure profiles and screw sizes on our trucks because those are the parts Fort Worth owners need after a storm. Odd-profile closures and custom trim we order direct, usually two to four business days out. If you’re not sure what you have, call and we’ll identify it on site.
If your Barrette roof is leaking or you’ve found screws in the gutter, the fix starts with a measured, written price. Straight scope, firm price, no surprises at final walkthrough. Call Bradford Remodeling Co Fort Worth at (682) 204-4897 to schedule your free estimate.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth at Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
