Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Ameristar Fence Installation: The Fort Worth Owner’s Guide
Ameristar fence installation in Fort Worth typically runs $3,500 – $9,000 for a complete perimeter, depending on linear footage, gate count, and whether we’re pulling old posts or setting new ones. We install Ameristar’s Montage, Classic, and Echelon systems, plus individual replacement sections when a tree limb or a Texas windstorm takes out a panel. Most owners call us because a section’s leaning after a storm, a gate’s dragging, or the powder coat’s showing rust at the post base where sprinkler water hits it every morning.
We’re an independent Fort Worth contractor, not an Ameristar distributor or affiliate. That means we tell you straight when an aftermarket post cap makes sense and when the OEM part’s the only call. The numbers below are real ranges we’ve quoted across Fort Worth neighborhoods from Tanglewood to Saginaw.
Which Ameristar Models This Applies To
The three Ameristar lines we install most in Fort Worth are Montage (residential, 4′ and 6′ heights, 2-rail and 3-rail), Classic (commercial-grade steel, usually 6′ or 8′, heavier gauge), and Echelon (aluminum residential, lighter and cheaper to ship). Each uses different post dimensions: Montage posts are typically 2″ square for 4′ panels and 2.5″ square for 6′. Classic runs 3″ square with reinforced bottom rails. If you’re matching an existing fence, measure the post face and the rail spacing before you call, or snap a photo of the gate hinge. We can identify the line from that hinge in about five seconds.
The gotcha most people hit: Ameristar’s residential and commercial panels don’t always share the same post-to-panel brackets. A Classic panel won’t drop into a Montage post without adapter plates. We keep those plates on the truck. Aftermarket brackets work fine for straight sections, but for gates we always use OEM Ameristar hinges because the load rating difference matters when a Fort Worth wind pushes a 50-pound gate against those hinge pins every afternoon.
Styles & brands we work with
Signs Your Ameristar Fence Installation Is Failing
- Post lean after heavy rain. Blackland clay in Fort Worth expands and contracts hard. If the post wasn’t set below the frost line with proper concrete collar, it walks. You’ll see the panel pulling the brackets or a gap opening at the top rail.
- Rust streaks bleeding from bolt holes. The powder coat seals the steel until a fastener scratches it. Once exposed, Fort Worth humidity does the rest. Touch-up paint won’t stop it; the section needs a clean, treatment, and re-coat or replacement.
- Gate dragging or sagging toward the latch side. Hinges wear unevenly on sloped Fort Worth lots. The gate’s weight migrates to the lower hinge, it bends a degree or two, and suddenly the latch won’t catch. We shim or replace the hinge post, then reset the gate square.
- Panel racks out of square after a storm. High straight-line winds can torque a panel 3 – 5 degrees without breaking welds. The rails stay intact, but the pickets bind. This usually isn’t a material failure; it’s the post shifting in saturated ground.
- Bottom rail corroded at the sod line. Sprinkler overspray, fertilizer salts, and weed trimmer contact strip the powder coat at the lowest rail. You’ll see blistering first, then flaking, then structural rust. This is the most common Ameristar failure in Fort Worth, bar none.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Ameristar fence install in Fort Worth runs $3,500 – $9,000. The range comes down to three things: linear feet (most backyards run 150 – 250 feet), how many gates and corners, and whether we’re removing an existing fence. A 200-foot Montage perimeter with two gates typically lands around $5,500 – $6,800. A 300-foot Classic install with a double-drive gate can push $9,000.
- Material: $18 – $32 per linear foot for panels, posts, brackets, and gates, depending on line.
- Labor and post setting: $12 – $18 per linear foot, including concrete in Fort Worth’s clay soil.
- Removal of old fence: $4 – $7 per linear foot, including haul-off.
- Gate hardware upgrade: $150 – $400 per gate for OEM Ameristar hinges and latches.
Every quote is written, line-itemed, and fixed before we start. No numbers move at the door. And every Ameristar fence installation we complete in Fort Worth carries the 365-Day Done Right Promise: if the section shifts, the gate drags, or the concrete cracks inside a year, we come back and correct it at no charge. That’s in writing, in your hand, at final walkthrough.
DIY or Call Us?
Ameristar fence installation isn’t a spring or a panel full of voltage, so the safety risk is lower than some jobs. But that doesn’t make it a weekend task. The part that gets homeowners hurt, honest truth, is the post-hole digging around Fort Worth gas and irrigation lines. Call 811 before any dig, and even then, hand-digging around marked lines through Blackland clay is a full day of work per 200-foot run.
What you can do yourself: straighten a racked panel by resetting one post if the concrete’s intact, replace a pickup cap, or swap a latch. What goes wrong fast: mixing concrete too wet in clay soil, setting posts shallow, misaligning a gate so it binds every time it moves. If the gate’s involved or more than two posts are moving, call us at (682) 204-4897. We’ll quote the section, not the whole fence, if that’s all you need.
FAQs
The steel lines (Montage and Classic) run 25 – 35 years in Fort Worth with proper post setting and drainage; the aluminum Echelon line runs 20 – 25 years. The variable is always the post base if sprinklers hit it daily, and the bottom rail if ground contact’s constant. Call (682) 204-4897 and we’ll tell you what your specific fence has left in it.
Yes, if the steel post isn’t rusted through and the concrete collar is intact, we can plumb the post, re-pack the base, and reset the panel. That’s a $200 – $400 repair versus a $600 – $900 section replacement. But if the post is bowed or the rust has eaten the wall thickness below grade, replacement is the only honest call.
For a typical 200-foot Fort Worth backyard with two gates and removal of the old fence, we’re on site 2 – 3 days. Post holes get dug and set day one, panels and gates day two, and cleanup, gate adjustment, and walkthrough day three. A section repair is usually done in a single afternoon.
We carry the common brackets, hinges, post caps, and touch-up coating for Montage, Classic, and Echelon on the truck every day. For full panels and custom gate widths, we order from Ameristar’s regional distribution, and Fort Worth’s close enough that standard orders arrive in 2 – 3 business days. We’ll confirm stock before we schedule, so you’re not waiting on a dangling quote.
Straight scope, firm price, no surprises at final walkthrough. If your Ameristar fence has a section failing, a gate dragging, or a rust problem at the post base, call (682) 204-4897 and one of us, usually Curtis Lane, will come read the site and give you a written number before any work starts. We also stock and install parts for KraftMaid, Cambria, and Silestone projects if you’re working through a bigger exterior or kitchen scope. The Garrison Standard is simple: every price in writing, every job guaranteed for a year, and a live person on the phone when you call.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth at Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
