Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Fence Installation: The Fort Worth Owner’s Guide
Unilock fence installation in Fort Worth runs $3,500 to $9,000 for a complete post-and-panel system built on a proper base, and we can typically source your specific Unilock series and start within a week to ten days depending on material availability. Most owners don’t call us about a fence that’s working fine. They call because a section heaved after a big rain, a gate post started leaning, or the original installer set posts without enough depth for our clay soil and the whole run is now wavy. The good news is that Unilock makes a disciplined product, and when the installation is done right the first time, that fence will outlast the operator.
We’re an independent installer in Fort Worth, not a Unilock dealer or affiliate. What we do is match your existing Unilock product to the right installation method, base material, and layout, then put it in with a written scope and a written price you read before we cut anything.
Which Unilock Models This Applies To
Unilock’s fence and freestanding-wall products fall into a few families: the Estate Wall system, the Lineo dimensional wall stone, and the Brussels Dimensional system are the three we see most across Fort Worth. The installation mechanics differ enough between them that you can’t assume one method fits all. Estate Wall uses a tongue-and-groove vertical joint that locks the face together without mortar, which means the base prep matters more than the block itself. Lineo is a contemporary rectangular profile with tighter tolerances. Brussels Dimensional is the traditional look, rougher texture, more forgiving on the cut rate.
Here’s the compatibility gotcha every owner should know: Unilock series are not designed to be mixed. If you have a failing section of Estate Wall and someone quotes you a cheaper Brussels Dimensional partial match, the joint lines won’t line up, the texture reads different in direct sun, and you’ll see the patch from the street. Verify the series name on your original paperwork if you kept it, or look for the Unilock stamp on an exposed face. We match what’s there.
For replacement work, we specify genuine Unilock units when the job requires an exact match on an existing run. If the whole fence is coming out and you’re open to alternative premium concrete units, we’ll show you options with equivalent compressive strength and freeze-thaw ratings. But we won’t silently substitute. That decision is in the written scope.
Styles & brands we work with
Signs Your Unilock Fence Installation Is Failing
- Leaning posts or gate posts. This is almost always a base problem, not a block problem. Fort Worth’s black clay shrinks and swells with moisture, and if the original installer poured a shallow footing or skipped the gravel base, the post moves over a season or two. The block above is just along for the ride.
- Separation at the joints. On tongue-and-groove Unilock systems, a widening gap means the base settled unevenly beneath the course. You may also see this after heavy rain when water finds a path under the wall. The fix is resetting the affected section, not caulking the joint.
- Cracked caps or chipped faces. Caps take the most abuse from sprinklers, weed trimmers, and Texas sun. A cracked cap may be a simple swap. A chipped face on a structural unit is more concerning if it sits below a point load like a gate hinge.
- Gate sag or latch misalignment. If the gate drags or the latch won’t catch, the hinge post has moved. This is the classic sign that the post footing was undersized for our frost line and soil movement. You won’t fix it by adjusting hinges alone for long.
- Efflorescence or discoloration. White chalky deposits on the face aren’t a structural failure, but they tell you water is moving through the wall. If it’s bad enough that the surface is spalling, that’s a freeze-thaw problem and the unit should be replaced before it becomes a hole.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the straight number for Fort Worth. A complete Unilock fence installation runs $3,500 to $9,000 depending on linear footage, wall height, access to the yard, and whether we’re doing a full removal or building new. A short 30-foot section reset or partial rebuild lands on the lower end. A full perimeter with gates, caps, and old-fence demolition pushes toward the top.
What drives the range more than anything is what’s under the wall. If the original base is good, we can work with it. If it’s garbage, we’re excavating it and building the correct base from scratch: compacted gravel, proper depth for Fort Worth clay movement, correct setback from any existing slab. That’s labor and material the bid has to account for. We won’t bury base costs in change orders later. Your written price covers the scope we agreed on, and the 365-Day Done Right Promise covers the work for a full year. If the fence moves, cracks, or fails in that window, you call us and we come back and fix it at no charge. That’s in writing, not in a handshake.
DIY or Call Us?
You can safely diagnose a lot of this yourself. Walk the line, check for leaning posts, look at the joints, check your gate swing. That tells you what you’re dealing with before you spend a dollar. What you shouldn’t do is pull a post out of an active wall or start rebuilding a section that ties into a gate. Concrete units in the 40-to-80-pound range hurt when they slip, and a wall that’s already moving can shift against you while you’re working on it. On a small straight section with a solid base, a competent homeowner can manage a cap replacement. Once you’re into base correction or structural resets, call us at (682) 204-4897 and we’ll look at it for free.
FAQs
A properly installed Unilock fence on a correct base lasts 20 to 30 years in Fort Worth before the freeze-thaw cycles and clay movement start to take a visible toll. The block itself will generally outlast the base or the gate hardware. If you’re seeing failure at year three or five, that’s an installation problem, not a product problem. Call (682) 204-4897 and we’ll tell you what you’re actually looking at.
Yes, in most cases a leaning section can be reset without buying new block. We excavate the affected run, fix the base, and re-lay the existing units. You only pay for new block if the units themselves are cracked or spalled. That’s a repair, not a rebuild, and it usually lands below the full-install price range.
A typical Fort Worth residential run takes 2 to 4 days from excavation to final cleanup, depending on footage and access. Partial resets are often done in a day. We don’t run multiple crews off one job site; the same crew starts and finishes, and the site is clean at close.
We don’t keep full pallets of Unilock on hand because every job is a different series and color, but we order direct for each project and verify the match before we commit. That’s part of why our price is written and firm: we know the material cost before we give you a number.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth at Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
