Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The Fort Worth Owner’s Guide
CGI kitchen remodeling in Fort Worth typically runs $14,000 to $45,000 installed, depending on cabinet layout, countertop material, and whether we’re replacing an existing setup or starting from studs. Most CGI-built or CGI-outfitted kitchens we see are failing in one of three places: cabinet box corner joints, countertop substrate separation, or hinge hardware that has stripped out of particleboard faces. We stock the common replacement components, keep a documented brand roster that includes CGI-compatible materials, and can usually start within a week of the written estimate.
Here’s the situation we walk into most often. A homeowner in Fort Worth has a kitchen that went in ten or twelve years ago, the doors are sagging, the drawers don’t close square, and there’s a soft spot near the sink where the substrate has been taking water. They don’t need a full gut. They need someone who knows which parts are still made, which ones are worth replacing, and which ones should be swapped for a better material in the same footprint. That’s the work we do.
Bradford Remodeling Co Fort Worth is an independent remodeling contractor. We are not affiliated with CGI, but we work with CGI kitchens and CGI-spec components on a regular basis, and we know how they fail in Texas heat and humidity.
Which CGI Models This Applies To
CGI built kitchens under several cabinet lines over the years, and the big gotcha for Fort Worth owners is that not every CGI line uses the same hinge boring pattern or drawer slide length. We’ve seen early-2000s CGI cabinets with 35mm cup hinges, and later production runs that used 40mm plate spacing. It’s a small difference that turns into a big problem when you order a replacement door and the hinge cups don’t line up. Before we touch anything, we pull a hinge, measure the boring distance, and match the slide rail length. That’s how we avoid ordering parts that arrive on the truck and don’t fit.
The pragmatic fork in the road is this: OEM CGI parts still exist for some lines, mostly door and drawer fronts, but availability is spotty and lead times run long from the few suppliers that still handle them. For structural parts (corner blocks, shelf cleats, box end panels, drawer boxes), a quality aftermarket equivalent is usually the better play. We cut drawer boxes from the same maple or birch plywood grade, match the finish, and we’re not waiting eight weeks on a back-ordered part that might not arrive before the holidays. The decision comes down to two things: whether the original finish can be matched (laminoates are harder than veneer), and whether the part takes visible wear or sits hidden behind a face frame.
Styles & brands we work with
Signs Your CGI Kitchen Remodeling Is Failing
- Doors sag or won’t stay closed: The hinge screws have stripped out of the particleboard stile, or the hinge itself has worn past its adjustment range. Tighten once and it’ll hold for a month. Then it strips again. The real fix is a threaded insert or a hinge relocation, not a longer screw.
- Drawers stick or slide rough: The nylon rollers on the original slides are flattened, or the slide rail has bent from years of overloaded pots. New undermount slides run $40 to $80 per drawer installed, and they’re the single best quality-of-life upgrade on a kitchen that still has original hardware.
- Soft spot near the sink or dishwasher: That’s substrate damage under the laminate or stone. Water got in through a failed seam or caulk line. Once the substrate swells, the countertop will never sit flat again, and any patching is temporary. The honest fix is a section replacement or a new countertop run.
- Corner cabinet shelf cracked or fallen: The plastic corner blocks, which is the failure point on most CGI boxes, are inside the cabinet at the back corners. In Fort Worth’s dry air and summer heat, those blocks get brittle, the glue lets go, and the shelf drops. We replace them with wood cleats and structural screws.
- Face frame separating from the cabinet box: You’ll see a hairline gap at the front, especially over the sink where humidity swings are worst. The original pin nails and glue have lost their hold. This one we actually disassemble, clean, re-glue with structural adhesive, and pin with a heavier gauge.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Fort Worth specifically, a full CGI kitchen remodel runs $14,000 to $45,000. The spread is driven by cabinet count, countertop square footage and material, and whether any walls move. A homeowner with an 8×10 kitchen and a straight cabinet run who keeps the footprint is on the low end. A homeowner adding an island, going to Cambria or Silestone on the counters, and rebuilding all the cabinet boxes is looking at the high end.
The written price includes parts, labor, haul-off of the old materials, and the pickup of any stock cabinets or CGI-compatible components. We give you the number before work starts. Every time. No numbers that move at the door. And the whole thing carries our 365-Day Done Right Promise: if the work fails inside a year, we come back and correct it at no charge. You get that in writing before a tool comes out of the trailer.
DIY or Call Us?
What you can check safely: pull a drawer and read the slide label for the manufacturer and length. Pull a hinge and measure the cup diameter and the screw spacing. Note where the finish has worn or the box has cracked. Those three details save us a trip on the estimate, and they tell us whether we’re looking at a repair or a replacement.
Where we’d pump the brakes: structural cabinet work, substrate removal under stone, and anything involving relocating plumbing or electrical behind the cabinets. We’ve pulled apart enough failed DIY fixes in Fort Worth to know that you don’t want unmounted quartz sitting on a water-damaged particleboard substrate while you figure out the next step. If you’re not sure, call us first. It costs nothing to have us look at it, and we’ll tell you straight if it’s a job you can handle.
FAQs
A CGI kitchen built and installed correctly in Fort Worth should give you 15 to 25 years of structure; the cabinet bodies, the hardware, the hinges, the slides, the frame. The finishes, the countertop seams, the drawer fronts, those are going to show age in 10 and start being a real issue at 15. The killer here is dishwasher steam. It breaks down the adhesives and the edge banding over time. If we’re rebuilding a kitchen and the dishwasher is original, we recommend relocating or replacing it at the same time. That little change adds years to the boxes.
Yes, and that’s the majority of the CGI work we do. We replace drawer boxes, swap hinges and slides, rebuild corner cabinets, replace face frames, and re-laminate or re-surface counters with Cambria or Silestone without gutting the whole room. A repair-heavy scope in Fort Worth usually runs $2,000 to $8,000, depending on what has failed. If the cabinet boxes are structurally sound, repair is usually the right call. If the boxes have water damage or the face frames have separated in multiple places, you’re better off rebuilding.
Most replacement scopes in Fort Worth run two to four days for cabinet and hardware work, and five to seven days if we’re pulling counters and redoing substrate. The exception is a full custom kitchen with an island and stone tops, which runs two to three weeks because the stone is cut offsite. We’ll give you a written schedule with the written price, and if we see a material lead time that’s going to blow the timeline, we flag it before we sign the scope.
We stock the common items that fail on CGI kitchens: 35mm and 40mm soft-close hinges, undermount drawer slides in the standard lengths, structural corner blocks, cabinet screws and threaded inserts, and edge banding in the standard finish colors. If we’re matching a door or drawer front, that’s a special order and takes longer. We also stock and install same-day parts from other picky brands we carry, including KraftMaid, Cambria, and Silestone, so the same crew that repairs your kitchen can match the rest of the house.
Straight scope, firm price, no surprises at final walkthrough.
Curtis Lane grew up in Los Angeles and learned his first trade skills at Los Angeles Trade-Technical College before spending two decades pulling permits across the Southwest. He and his crew have been working Fort Worth for years, on everything from gut-rehab kitchens near the Stockyards to full additions on the south side. Curtis is known for reading a job site before he reads the quote, which means his scopes don’t grow legs mid-project. On weekends he’s usually in the garage rebuilding something that doesn’t need rebuilding, which his wife considers a character flaw and he considers continuing education.
If your CGI kitchen is failing in Fort Worth, call (682) 204-4897 for a free estimate. A live person answers, 24/7, and you’ll get a written price before any work starts.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth at Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
