Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Roofing: The Fort Worth Owner’s Guide
We stock and install CGI-compatible roofing components across Fort Worth, with most replacement parts running $400 to $1,800 installed depending on the component and roof access. If you’ve got a failed fastener, a cracked panel, or a flashing seam that’s opened up after a hailstorm, we can usually match the part and get it swapped the same week. Most owners discover a problem either after a storm blows through, or when a slow leak finally darkens a ceiling corner and they trace it back to the roof.
You’re here because something’s failing, and you want the right part, the honest price, and a repair that holds through the next North Texas wind season. That’s exactly what this page covers. We’re an independent service provider, not affiliated with CGI, which means we tell you straight when an OEM part is worth the wait and when a quality aftermarket match does the job for less.
Which CGI Models This Applies To
CGI manufactures metal roofing systems under several lines common in Fort Worth homes: the Horizon Shingle, Slate, Tile, and standing-seam profiles like the Valor series. The Horizon line is what we see most on suburban ranches and two-stories across Tarrant County. The parts we handle most often include panel clips, closure strips, ridge caps, Z-flashing, eave trim, and the coated fasteners CGI specifies for wind uplift.
Here’s the gotcha most owners run into: CGI fasteners are not interchangeable with generic roofing screws. The factory calls for specific pancake-head screws with a sealing washer matched to the panel profile, and using a generic screw from a big box store will either under-drive and loosen, or over-drive and crush the seam. If you’ve lost the original packaging, check the panel label under the eave or photograph the profile and text it to us. We can usually identify the series by the rib spacing and panel width. For older installs where the panel was discontinued, a matched aftermarket profile from a supplier like McElroy or Fabral often lines up correctly, and we’ll tell you before ordering whether it’s a true match or a compromise.
Styles & brands we work with
Signs Your CGI Roofing Is Failing
The failure pattern here is predictable if you know what to look for. Here’s what we see walking roofs across Fort Worth:
- Rust staining around fasteners. The neoprene washer under the screw head degrades after six to ten years of Texas sun, letting moisture sit against the screw. You see brown streaks running down from the fastener line.
- Oil-canning that wasn’t there at install. Panels that look wavy or ripple in direct light are often telling you the clips have shifted or the substrate has settled. This is usually a fastener or clip issue, not a panel defect.
- Lifted ridge cap or eave trim after wind. CGI’s profile relies on trim being screwed at specific intervals. Once a trim piece starts lifting, water travels underneath it and the rot begins at the decking.
- Leaks at the transition points only. Where the metal meets a chimney, vent pipe, or wall, the flashing was either under-cut or the sealant has gone brittle. Panel-to-panel leaks are rare on a properly installed CGI roof; transition leaks are common.
- Granules appearing in gutters. This applies to the stone-coated CGI profiles like Horizon Shingle. When the stone coating starts shedding, the steel underneath is exposed and the panel’s lifespan drops sharply.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Fort Worth homes, CGI roof repair typically runs $400 to $1,800 installed. A simple fastener replacement or minor trim re-securing sits at the low end. Replacing multiple damaged panels, rebuilding a flashing transition, or swapping out a failed ridge cap assembly pushes toward the middle of that range. A full section replacement where decking is compromised can reach the top of it.
The range is driven by three things: roof pitch and access, whether the part is still in production or needs a matched aftermarket equivalent, and how much decking damage we find once the panel comes off. You get a written line-item price before we start, parts and labor separated, and that number does not move at the door. Every repair carries the 365-Day Done Right Promise: if it fails within a year, we return and correct it at no charge. Straight scope, firm price, no surprises at final walkthrough.
DIY or Call Us?
There are a few things an owner can safely check without getting on a ladder: look for rust streaks from the ground, check gutters after a storm for loose trim pieces or stone granules, and inspect the ceiling in rooms directly under a roof transition. What you should not do is walk a metal roof without fall protection, or attempt to back out and replace fasteners yourself. Over-driving a screw by a quarter turn is the difference between a sealed seam and a leak you won’t find until the next downpour. Metal roofing ties into waterproofing in ways that take one wrong move to compromise.
Curtis Lane and our crew will walk the roof, photograph what we find, and give you a written price before any work begins. Call (682) 204-4897 and we’ll schedule the inspection.
FAQs
A properly installed CGI metal roof should last 40 to 60 years in Fort Worth, though the stone-coated profiles like Horizon Shingle typically need a fastener and sealant tune-up around the 10 to 12-year mark because the Texas heat degrades sealing washers faster than the steel panel itself. Call (682) 204-4897 for an inspection if yours is hitting that age.
A dented or scratched panel can often be touched up with a color-matched coating, but any panel with a puncture, a torn seam, or fastener holes that have wallowed out should be replaced rather than patched. We’ll tell you which applies to your roof before you spend a dollar.
For a single panel or a small section, the work is usually done in half a day once materials are on site. Removing and reinstalling without damaging the surrounding panels is the slow part, and we’d rather take the time than rush it.
We stock common fasteners, washers, closure strips, and sealants in our trucks, and we order panels, ridge caps, and trim pieces by profile match. Most parts arrive within a few business days in Fort Worth, and we’ll give you a firm install date when we hand you the written quote.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth at Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
