Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Bathroom Remodeling: The Fort Worth Owner’s Guide
A full Moen bathroom remodeling project in Fort Worth typically runs $9,000 to $28,000 installed, depending on whether you’re refreshing fixtures or tearing down to the studs. We stock Moen faucets, showerheads, valves, and trim kits on our trucks, and most Moen part replacements happen in a single visit. The usual story we hear: you’ve got a Moen shower valve that won’t hold temperature, a cartridge that’s seized, or a finish that’s pitted from Fort Worth’s hard water, and you’re trying to figure out whether to replace the part or rethink the whole bathroom.
Here’s the straight answer: if the valve body is sound, you replace the cartridge or trim. If you’re already opening walls to fix a leak, that’s when a Moen bathroom remodeling job makes sense, because you can upgrade to a Moen M-CORE or Posi-Temp system while the wall is open and get a written price before we start.
Which Moen Models This Applies To
We work on the full Moen line: Posi-Temp, Moentrol, M-CORE, and the older Chateau and Legend series that show up constantly in Fort Worth homes built in the 1980s and 1990s. The Posi-Temp valve is the most common one we see, and it uses the Moen 1222 cartridge. Moentrol uses the 1225. Get those two mixed up and the job goes sideways, so we check the brass body marking before ordering anything.
Here’s the compatibility gotcha most homeowners don’t know: Moen has changed trim styles over the years, and not every handle kit fits every valve body. A Moen “Alder” or “Genta” trim kit will fit a Posi-Temp valve, but it will not fit an older Moentrol valve without a valve swap. That’s the difference between a $300 trim refresh and a $1,200 valve replacement. For OEM versus aftermarket: we install genuine Moen parts on anything in warranty, and we’ll use quality aftermarket cartridges when a customer wants to save money on a 20-year-old valve that’s already out of warranty. We’ll tell you which is which before you pay.
Styles & brands we work with
Signs Your Moen Bathroom Remodeling Is Failing
- Water temperature won’t stay consistent. You set the handle and 30 seconds later it’s cold or scalding. That’s the Moen pressure-balancing cartridge wearing out, and Fort Worth’s mineral-heavy water accelerates it.
- The handle is stiff or stuck. Hard water deposits build up on the cartridge and make the handle fight you. Forcing it is how plastic stems snap inside the valve.
- Drip, drip, drip from the tub spout. A constant drip with the handle off means the cartridge isn’t sealing. On a Moen Posi-Temp, that’s usually a worn 1222 cartridge, not a washer you can adjust.
- Water leaking behind the wall or onto the floor. This is the one that costs real money. A cracked valve body or failed connection behind the tile means opening the wall, and that’s when you’re into bathroom remodel territory in Fort Worth, not just a cartridge swap.
- Finish flaking or pitting. Moen’s brushed nickel and chrome hold up well, but Fort Worth’s water chemistry can pit lower-end finishes in as little as eight years. The fix is a new trim kit, not a whole new valve.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here are real numbers for Fort Worth. A Moen cartridge replacement (parts and labor) runs $180 to $340. A full Moen shower valve replacement, meaning we open the wall, swap the valve body, and patch the drywall, runs $850 to $1,600. A complete Moen bathroom remodeling project, which includes new valve, trim, fixtures, and often tile or surround work, lands between $9,000 and $28,000.
| Job Type | Installed Price Range |
|---|---|
| Moen cartridge replacement | $180 – $340 |
| Moen valve body replacement | $850 – $1,600 |
| Moen tub-to-shower conversion | $3,500 – $10,000 |
| Full Moen bathroom remodel | $9,000 – $28,000 |
Every quote is a written line-item price before we touch a tool. No change orders because we measured wrong, no “by the way” add-ons at the door. The 365-Day Done Right Promise covers the entire project: if anything we installed fails inside a year, we come back and fix it at no charge, with that guarantee signed and in your hand at close. We pull permits when the job requires them, and we pass inspections before we call it done.
DIY or Call Us?
Swapping a Moen handle or escutcheon plate is something a careful homeowner can do with a hex key and a screwdriver. We’ll even tell you how if you call. But anything involving the cartridge inside the valve, or anything that requires shutting off water at the main and opening walls, is where DIY gets expensive. We’ve rebuilt bathrooms in Fort Worth where a homeowner snapped a cartridge stem off inside the valve body, and the original $300 job became a $1,400 valve replacement. Moen cartridges are under constant water pressure, and Fort Worth’s hard water welds them into place. If you’re not certain, call (682) 204-4897 and we’ll walk you through what you’re looking at over the phone before scheduling anything.
FAQs
A genuine Moen 1222 or 1225 cartridge typically lasts 10 to 15 years in Fort Worth, but hard water from the Trinity River aquifer can shorten that to 8 years or less. If your cartridge is older than eight years and you’re already seeing temperature swings or stiffness, it’s on borrowed time. Call (682) 204-4897 and we’ll give you an exact price to swap it.
Yes, if the brass valve body is sound, the fix is a new cartridge and possibly new trim, which is a fraction of the cost of a full Moen bathroom remodeling project. If the valve body is cracked or the ports are corroded, repair isn’t safe and we’ll tell you straight. Estimates are free.
A cartridge swap takes about 45 minutes. A valve body replacement takes half a day because we’re opening the wall, shutting down water, and patching the drywall. A full Moen bathroom remodeling job in Fort Worth runs one to three weeks depending on tile, glass, and whether we’re moving plumbing. We’ll give you a written schedule before you sign.
We stock Moen 1222 and 1225 cartridges, common trim kits, and Moen showerheads and tub spouts on our trucks, along with parts for KraftMaid cabinetry, Cambria and Silestone surfaces, so most Fort Worth jobs get done in one trip. If you need an obscure Moen finish or a discontinued series, we order it and usually have it in two to three days. Call (682) 204-4897 and we’ll check the truck before you book.
Bradford Remodeling Co Fort Worth is an independent service provider and is not affiliated with Moen Incorporated. When you’re ready to talk through your bathroom, call (682) 204-4897. Curtis Lane and the crew will give you a straight scope, firm price, and a written 365-Day Done Right Promise before any work starts. Free estimates, every time.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth at Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
