Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Windows & Doors: The Fort Worth Owner’s Guide
We stock and install Mr-Glass-compatible windows and door parts across Fort Worth, with typical hardware swaps running $180 – $450 installed and full glass replacement landing between $350 and $1,400 depending on pane size and gas fill. Most hardware jobs are done in a single visit, and we carry common Mr-Glass series hardware on the truck so the fix usually happens the day we show up. The way most Fort Worth homeowners find us: a window that drops when you let go of the sash, a patio door that drags, or a lock that stops catching clean.
You’ll know the part failed the same way our clients describe it on the phone. The window still sits in the frame, the glass isn’t cracked, but it won’t stay up, won’t seal, or won’t lock. Something internal wore out. That is a parts problem, not a full replacement problem, and it’s cheaper to fix than most people expect.
Which Mr-Glass Models This Applies To
Mr-Glass produced windows and patio doors under a handful of series names through the years, and the hardware is not universal between them. The big compatibility split is single-hung versus horizontal slider. Single-hung sashes ride on block-and-tackle balances or spiral balances depending on the production year. Sliders run on nylon roller assemblies that wear flat on the bottom rail. The pivot bars, tilt latches, and keeper hardware differ by series, and a part from one series will not seat correctly in another even when it looks close.
Before you order anything, check the material sticker or engraving on the sash frame. The series code is often stamped on a corner gasket or printed on the spacer bar between the glass panes. If the sticker is gone, measure the sash width and the glass thickness to the nearest sixteenth of an inch. For slider doors, pull the panel and read the roller housing. We match OEM Mr-Glass parts where the manufacturer spec is still available, and use proven aftermarket equivalents for older series where the original is discontinued. In those cases we’ll show you both prices in writing before we touch the window.
In Fort Worth, the heat does something specific to these units. Rubber compression seals bake out faster than the hardware fails. A window that has been baking on a west-facing wall since the early 2000s may need a new weatherstrip the same time it needs a new balance, and fixing both at once is a $75 – $120 add, not a second trip.
Styles & brands we work with
Signs Your Mr-Glass Windows & Doors Is Failing
- The sash drops hard when you release it. Block-and-tackle or spiral balance no longer holds tension. If you hear a rattle inside the jamb when you slide the sash up, a balance shoe or pivot bar has broken free.
- The window closes fine but you feel air moving around the edges. Compression seals and wool pile strips lose material over years of DFW heat and dust. The hardware is fine; the sealing element is gone.
- The patio door sticks in one spot and glides everywhere else. The roller on that side has flat-spotted. Fort Worth clay dust works its way into the roller bearing and grinds it until the wheel stops turning.
- The lock engages but doesn’t catch the keeper. Misaligned keeper or a worn latch hook. This is a $35 – $70 hardware fix in most Mr-Glass door applications, and it’s the difference between a door that actually locks and one that looks locked.
- The window tilts for cleaning but won’t seat back in the frame. Tilt latches have worn shoulders, or the pivot bar slipped out of the shoe. When this happens, the sash will sit crooked in the opening.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Fort Worth window and door parts fall into predictable buckets. Balances, tilt latches, pivot bars, and lock hardware run $180 – $450 installed depending on how many units need the same part. A full glass unit replacement on a Mr-Glass window runs $350 – $1,400 installed, and that swings on the glass package, whether it’s a low-E or clear unit, and whether the sash needs to be deglazed and rebuilt or the entire sash replaced.
The range exists for a reason. A single double-hung window needing two new balances is a one-hour job at the low end. Three patio door rollers plus a keeper and weatherstrip starts adding trip time and disassembly. We write the part numbers, the unit price for each, and the labor as separate lines before we start. Nothing moves at the door. And when the job is done, you get the written guarantee in your hand under the 365-Day Done Right Promise. If the part fails or the install doesn’t hold inside a year, we return and correct it at no charge.
DIY or Call Us?
You can check what you’re up against without touching a screwdriver. Confirm the series code on the sash or spacer bar. Check whether the window drops on one side or both. If a patio door is dragging, lift the panel slightly and see which side gives. That tells you a lot without removing anything.
Here is the honest line: window balances are under spring tension, and a tilt-latch repair on a double-hung means working with the sash out of the frame. If a block-and-tackle balance lets go while the sash is out, you are looking at a cracked sash corner, a broken jamb liner, or worse. A patio door panel is heavy and easy to chip if you force the wrong roller. This is not the place to learn a new skill at the expense of a window you already own. If the failure involves a tensioned balance or a glass unit, call (682) 204-4897 and let a uniformed, background-checked tech put eyes on it. The estimate is free.
FAQs
In Fort Worth, we see balances and rollers last 12 to 20 years before they lose function, and the variable is exposure. South- and west-facing windows cycle through more heat expansion, and those seals and tension parts fail first.
Rarely. A roller with a flat spot cannot be rounded back out, and a balance that has lost spring tension is done. What we can often do is replace only the worn sub-component, like a roller wheel inside an otherwise good housing, which keeps the job smaller than a full assembly swap. Call (682) 204-4897 if you want us to look at the exact part before you spend anything.
Most single-window hardware jobs run 45 minutes to two hours on site. A patio door roller and keeper replacement is usually under 90 minutes. Full glass unit replacements run longer because the old unit has to come out clean and the new one sealed and shimmed square. If we stock the part on the truck, the job is done in one visit.
We stock common Mr-Glass series hardware on the truck: balances, tilt latches, pivot bars, keepers, and roller assemblies. For oddball series or discontinued glass sizes, we order and quote the part before any work starts. You’ll see the part cost and the lead time in writing. We also carry parts for KraftMaid, Cambria, and Silestone product lines. Call (682) 204-4897 for a free estimate.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fort Worth, serving Fort Worth and nearby areas.
